Dry Ice Blasting Mold in EAST IRVINE, California
Chemical-free mold removal for wood, framing, and crawl spaces
Dry Ice Blasting Mold in EAST IRVINE, California lifts mold off lumber, sheathing, and framing with frozen CO2 pellets instead of sandpaper, chemicals, or tear-out. If you have found black mold growth on attic rafters, crawl space joists, or bathroom studs, we blast it back to bare wood, HEPA-vacuum the debris, and verify the result with air sampling. Our team handles dry ice mold remediation in EAST IRVINE for homes and commercial buildings, often the same day you call.
What Dry Ice Blasting Mold in EAST IRVINE, California Actually Does
Dry Ice Blasting Mold in EAST IRVINE, California is a media-blasting process that uses solid carbon dioxide pellets accelerated through a specialized nozzle to strip mold, mildew, and surface contamination off building materials. The pellets hit the surface at roughly -109 degrees Fahrenheit and sublimate on impact, lifting spores and biofilm without water, abrasive grit, or chemical residue. On a typical job we blast framing, subfloor, roof sheathing, and crawl space joists, then HEPA-vacuum the loosened material and fog the cavity with an antimicrobial coating.
Most EAST IRVINE calls we run come from three places: a slow supply-line leak behind a bathroom wall, condensation on attic sheathing during the marine-layer months, and crawl space humidity that never quite dries out. By the time a homeowner sees the musty odors or a dark stain, mold has usually been growing for weeks. That is where dry ice mold remediation in EAST IRVINE earns its keep, because it cleans the actual structure instead of just wiping the visible face of it. If you have been searching for dry ice blasting mold near me EAST IRVINE, we can inspect and quote the same week.
Why Dry Ice Blasting Beats Scraping and Chemicals
Dry ice blasting removes mold from wood and framing without water, sand, or solvents, which means less demolition, faster turnaround, and no chemical residue left behind in your home. Here is what that looks like on a real EAST IRVINE job.
No Secondary Waste Stream
Sandblasting and soda blasting leave hundreds of pounds of grit to bag and haul away. Dry ice sublimates on contact, so the only waste is the mold debris we capture with a HEPA vacuum and biohazard bags. On a 600-square-foot attic, that can cut disposal volume by 80% and shorten the job by a full day.
Cleans Without Wetting
Water-based washing pushes moisture into porous framing, which is exactly what mold needs to come back. Dry ice blasting mold removal services EAST IRVINE uses no liquid at all, so studs and sheathing stay dry and the cavity can be encapsulated the same day instead of waiting 48 to 72 hours for drying.
Reaches Profiles and Crevices
A wire brush skips the corners of a joist and the lap joint on roof sheathing. The CO2 stream follows the profile of the wood, cleaning edges, nail heads, and tight framing intersections where black mold growth hides. That is the difference between a surface wipe and a real dry ice mold removal EAST IRVINE result.
No Chemical Odor or Residue
Some homeowners react to the smell and residue of bleach or quaternary cleaners. Dry ice blasting uses no chemicals on the blast pass, and we follow with a low-odor antimicrobial coating such as Concrobium or Benefect. You can reoccupy most treated rooms within 24 hours after clearance testing.
How Our Dry Ice Blasting Mold Process Works
Every job follows the same five stages, from the first moisture reading to the final clearance test. Here is what you will see and hear on site, and how long each stage takes.
Inspection and Mapping
We start with a moisture meter, a thermal imaging camera, and a boroscope inspection camera to find every wet pocket, not just the visible stain. Readings get marked on a sketch of the room or cavity. A typical inspection runs 45 to 90 minutes, and you get the findings before any equipment comes off the truck.
Containment and Air Control
We hang plastic sheeting with duct tape, set up a negative air machine with HEPA filters, and stage an air scrubber so spores cannot drift into the rest of the house. Technicians wear personal protective equipment, disposable coveralls, and N95 respirators. Setting containment on a single room usually takes 60 to 90 minutes.
Dry Ice Blasting
The dry ice blasting machine feeds CO2 pellets through a nozzle at 150 to 300 psi depending on the substrate. We work in passes, starting at the top of the cavity and moving down, then switch to a smaller nozzle for corners and framing joints. A 400-square-foot attic typically takes three to five hours to blast clean.
HEPA Vacuum and Antimicrobial Coat
Loose debris gets captured with a HEPA vacuum and sealed into biohazard bags. We then fog the cavity with a fogger using Benefect or RMR-86, and apply an encapsulation sealant to framing that will stay exposed. This stage runs two to three hours and locks down any residual spores the blast loosened.
Verification and Clearance
An air sampling pump and InstaScope readings confirm spore counts have dropped to normal outdoor baseline before we pull containment. You receive the before-and-after lab results in writing. Post-remediation testing is scheduled 24 to 48 hours after the final coat cures, and we do not call a job done until it passes.
Mold Remediation Experience You Can Verify
Our technicians are trained on the IICRC Certified Mold Remediation standard and follow California Department of Public Health guidelines for spore assessment and clearance. We hold a California Contractors State License Board (CSLB) license and carry EPA Lead-Safe Certification for work in pre-1978 housing stock. Every blast job is supervised by an ACAC Certified Mold Inspector who signs off on containment, blast pressure, and final air sampling. We are also members of the Indoor Air Quality Association (IAQA) and hold NORMI certification, which means the same standards used on commercial losses get applied to your attic or crawl space.
- IICRC Certified Mold Remediation technicians on every blast crew
- ACAC Certified Mold Inspector supervising containment and clearance
- EPA Lead-Safe Certification for older EAST IRVINE housing stock
- California Contractors State License Board (CSLB) licensed contractor
- NORMI certification and IAQA membership for air quality protocol
Why Homeowners Choose Our Dry Ice Blasting Mold Team
We are a local mold remediation crew, not a franchise call center. That means the person who inspects your attic is the person who runs the blast and signs the clearance test, and you get a straight answer about what the job needs.
Same-Week Scheduling
Most EAST IRVINE inspections get booked within three business days, and emergency mold testing services can often be dispatched the same day. If you have active water damage feeding the mold, tell us on the phone and we will prioritize the call.
Written Scope Before We Start
You get a written scope with the containment plan, blast areas, and testing protocol before any equipment is staged. No surprise line items after the fact. If the scope changes because we find a second wet cavity, we stop and talk to you first.
Dry Ice Mold Remediation EAST IRVINE Focus
Dry ice is not a sideline for us. We run dedicated blasting machines, keep CO2 pellet supply on hand, and know how the process behaves on the wood framing common in this part of California. That focus is why dry ice mold remediation EAST IRVINE homeowners get a clean, dry result.
Clearance Testing Included
Every dry ice blasting mold removal services EAST IRVINE job ends with air sampling, not a verbal all-clear. We compare indoor spore counts to an outdoor control sample and give you the lab report. If it does not pass, we re-clean at no additional charge.
What Our Dry Ice Blasting Mold Service Includes
Every dry ice blasting mold job includes the inspection, containment, blasting, HEPA vacuuming, antimicrobial coating, and clearance testing described below. If a cavity needs new framing or a duct system needs replacement, we will tell you before work starts so there are no surprises on the invoice.
What's Included
Moisture Mapping and Inspection
We use a moisture meter, thermal imaging camera, and boroscope inspection camera to find every wet pocket before blasting. You get a sketch of the affected areas and the moisture readings that justify the scope.
Containment and Negative Air
Plastic sheeting, duct tape, and a negative air machine with HEPA filters seal the work zone. An air scrubber runs continuously so spores released during blasting get captured instead of drifting into the rest of the house.
Dry Ice Blasting of Framing
CO2 pellets strip mold off studs, joists, sheathing, and subfloor at 150 to 300 psi. We switch nozzle sizes for corners and tight framing joints so the blast follows the profile of the wood.
HEPA Vacuum and Debris Removal
Loosened mold debris gets captured with a HEPA vacuum and sealed into biohazard bags. We do not leave bagged debris on site overnight; it leaves with us the same day.
Antimicrobial Fog and Encapsulation
A fogger applies Benefect or Concrobium to the cavity, and we roll encapsulation sealant onto framing that stays exposed. This locks down residual spores and gives the wood a clean surface.
Clearance Air Sampling
An air sampling pump and InstaScope readings confirm spore counts dropped to baseline before containment comes down. You receive the lab report in writing, and we re-clean at no charge if the test does not pass.
Mold Problems We Solve With Dry Ice Blasting
Most mold calls start with a smell, a stain, or a water bill that does not add up. Here are the problems we solve most often for EAST IRVINE homeowners and what happens if they are left alone.
Black mold growth on attic roof sheathing
Spores circulate through the HVAC system and into bedrooms, and the staining spreads along the sheathing every wet season until the wood is too degraded to hold fasteners.
We contain the attic, blast the sheathing and rafters with dry ice, HEPA-vacuum the debris, and apply encapsulation sealant. Clearance testing confirms the spore count dropped before we close the attic up.
Musty odors coming from the crawl space
The smell rises into living space and worsens each spring. Left alone, joists and subfloor absorb enough moisture to support rot as well as mold.
We inspect with a boroscope, blast the joists and subfloor clean, fog the cavity, and seal the framing. Because dry ice adds no water, the crawl space does not need a 72-hour drying window afterward.
Bathroom mold behind tile after a supply-line leak
The visible mold on the drywall is only part of it. Studs stay wet behind the tile, and new drywall installed over contaminated framing grows mold again within months.
We open the wall, blast the studs and blocking, HEPA-vacuum the cavity, and fog with an antimicrobial. Your contractor then hangs new drywall on clean, dry framing instead of contaminated wood.
HVAC mold contamination spreading through vents
Every time the system runs, spores get pushed into every room. Occupants notice allergy symptoms that seem worse indoors than outdoors.
We isolate the air handler, blast accessible metal and framing surfaces, and pair the blast with mold fogging treatment for the duct interiors. Air quality and mold testing confirms the airborne count before the system goes back into service.
When Dry Ice Blasting Mold Is the Right Call
A roof leak stained the attic sheathing but the wood is still structurally sound.
We contain the attic, blast the sheathing and rafters with CO2 pellets, vacuum the debris, and apply encapsulation sealant to the cleaned wood.
The attic returns to bare, dry wood without replacing sheathing, and clearance testing confirms spore counts are back to outdoor baseline.
A bathroom remodel revealed mold on the studs behind the old tile.
We blast the exposed framing, fog the cavity with Concrobium, and verify with air sampling before the new drywall goes up.
The remodel continues on schedule with clean framing, and you avoid the cost of reframing the wall.
A crawl space has musty odors and mold on the joists from years of humidity.
We inspect with a boroscope, blast the joists and subfloor, HEPA-vacuum, and seal the framing with encapsulation sealant.
The odor source is removed rather than masked, and the sealed framing resists moisture during the next wet season.
A commercial tenant space has mold on exposed structural steel and framing after a roof failure.
We phase the work around business hours, set containment with negative air, and blast the structural surfaces clean.
The tenant reoccupies the space within 24 hours of clearance testing, and the landlord has documented lab results for the file.
Tools and Methods We Use on Every Job
Tools & Equipment
Dry Ice Blasting Machine
Feeds CO2 pellets through a nozzle at 150 to 300 psi to strip mold off framing, sheathing, and structural steel without abrasive media.
HEPA Vacuum and Air Scrubber
Captures loosened spores and debris during and after blasting so they do not settle back onto cleaned surfaces or drift out of containment.
Negative Air Machine
Keeps the work zone under negative pressure with HEPA filters, so air flows into containment rather than into living space.
Thermal Imaging Camera and Moisture Meter
Finds hidden wet pockets before blasting and confirms framing is dry enough to encapsulate afterward.
Boroscope Inspection Camera
Lets us see inside wall cavities and crawl spaces without opening every surface, so the blast scope matches the actual mold spread.
Air Sampling Pump and InstaScope
Measures airborne spore counts before and after the job, giving you documented clearance instead of a verbal all-clear.
Fogger
Applies Benefect, Concrobium, or RMR-86 to cavity surfaces the blaster cannot reach, knocking down residual spores after the blast pass.
Methods
IICRC Certified Mold Remediation protocol
Our containment, removal, and clearance steps follow the IICRC standard, which is the same framework used on commercial mold losses. That means documented moisture readings, defined containment boundaries, and post-remediation verification on every job.
California Department of Public Health guidelines
Spore assessment and clearance follow CDPH guidance, including outdoor control samples for comparison. This is how we prove the indoor count returned to normal rather than just showing you a clean-looking board.
Negative pressure containment
We seal the work zone with plastic sheeting and duct tape and run a negative air machine with HEPA filters. Air flows into containment, not out, which protects the rest of the house during blasting.
Antimicrobial fogging and encapsulation
After blasting, we fog the cavity with Benefect or Concrobium and roll encapsulation sealant onto exposed framing. The fog knocks down residual spores; the sealant keeps the cleaned wood from re-contaminating.
How Dry Ice Blasting Mold Runs in EAST IRVINE
EAST IRVINE sits close enough to the coast that marine-layer humidity hangs around through the spring and early summer, and that moisture shows up as condensation on attic sheathing and crawl space joists. The housing stock matters too: the older villages near University Park and Woodbridge have original framing and sometimes original bathroom venting, while the newer construction around the Great Park and Portola Springs tends to have tighter building envelopes that trap moisture when a vent fails. We scope dry ice mold remediation EAST IRVINE jobs around those patterns, prioritizing attic and crawl space cavities where condensation, not a plumbing leak, is the moisture source. If you need dry ice blasting mold removal for homes in EAST IRVINE, we inspect first and blast second, because blasting a cavity that still has an active moisture source just means the mold comes back. California Department of Public Health clearance standards apply to every job, and we schedule post-remediation testing 24 to 48 hours after the antimicrobial coat cures.
Service Areas
Older attics with original roof sheathing are common here, and sheathing condensation is the most frequent mold call we get in the neighborhood.
Bathroom supply-line leaks behind original tile are a recurring source of framing mold in the older condos and townhomes near the lake.
Crawl space humidity runs higher on the slopes here, and joists benefit from blasting plus encapsulation sealant to hold up through the wet season.
Newer, tighter construction means a failed bath vent can push moisture into the attic fast; we see mold on sheathing within weeks of a vent failure.
Mature landscaping and shaded roofs keep sheathing damp longer after rain, which makes attic inspections worthwhile each spring.
Local Considerations
Marine-layer humidity in spring and early summer
Condensation forms on attic sheathing and crawl space framing, feeding mold without any visible leak. We prioritize those cavities for blasting and encapsulation.
Tight building envelopes in newer construction
Moisture from a failed bath vent or dryer duct has nowhere to escape, so mold establishes on sheathing quickly. Early inspection keeps the blast scope small.
Original framing in older villages
Aged wood absorbs moisture differently and needs lower blast pressure to avoid surface damage, so we adjust nozzle pressure by substrate.
Attic Sheathing Restored in Northwood
A roof leak went unnoticed for two seasons, and black mold growth covered roughly 300 square feet of roof sheathing and rafters. Moisture meter readings on the sheathing were in the 24% range, well above the dry standard.
We contained the attic, blasted the sheathing and rafters, HEPA-vacuumed the debris, and applied encapsulation sealant. Post-remediation air sampling came back at outdoor baseline, and sheathing moisture dropped to 11%.
Maintenance & Follow-up
Fix the roof leak before the next rainy season and recheck attic humidity each spring. A $15 hygrometer in the attic catches condensation early.
The homeowner had dealt with a musty smell for two summers. A boroscope inspection found mold across the floor joists and subfloor, with relative humidity in the crawl space holding above 70%.
We blasted the joists and subfloor, fogged the cavity with Benefect, and sealed the framing. The odor cleared within a day, and clearance testing confirmed spore counts had returned to normal.
Maintenance & Follow-up
Keep a vapor barrier intact and run a crawl space dehumidifier during the humid months. Recheck framing moisture each fall.
A supply-line leak behind the tile soaked the studs for weeks. The homeowner had a quote to reframe the entire wall, and the visible drywall mold was only a fraction of the affected area.
We opened the wall, blasted the studs and blocking, HEPA-vacuumed the cavity, and fogged with Concrobium. The framing tested dry at 12%, and the contractor hung new drywall on clean wood two days later.
Maintenance & Follow-up
Check the supply line fittings under the sink annually and watch for tile grout cracks that let moisture into the wall cavity.
What Dry Ice Blasting Mold Costs
Typical 2026 pricing for dry ice blasting mold in EAST IRVINE runs $1,800 to $6,500, with most attic and crawl space jobs landing near $3,200. The biggest cost driver is square footage blasted, followed by containment complexity and whether the job includes clearance testing. Dry ice blasting often costs less overall than tear-out and replacement because you keep the original framing and drywall. We quote the blast scope in writing before work starts, and if we find a second wet cavity mid-job, we stop and talk to you before adding it.
Pricing Factors
Square footage blasted
A single bathroom cavity might be 80 square feet of framing; a full attic can be 1,200. Blasting time and CO2 pellet consumption scale directly with area, which is why square footage is the largest line item.
Number of affected cavities
Each cavity needs its own containment setup and clearance sample. A job with an attic and a crawl space takes roughly twice the containment labor of a single-cavity job.
Containment complexity
An open attic is straightforward to seal. A finished basement with furniture, HVAC registers, and limited access takes longer to contain and protect, which adds labor hours.
Access and height
Crawl spaces with 18 inches of clearance and attics with steep roof pitches slow the work down. Technicians spend more time positioning equipment and less time blasting.
Clearance testing scope
A single air sample is inexpensive; a room-by-room protocol with outdoor controls costs more. We recommend the fuller protocol on any job where occupants have reported symptoms.
Antimicrobial and encapsulation products
Concrobium, Benefect, and encapsulation sealant are priced by coverage area. A large attic with exposed framing needs more sealant than a small bathroom cavity.
Investment Range
$1,800 - $6,500 depending on scope
Based on project scope
Value You Get
You are paying to keep the framing you already have. Tear-out and replacement on a typical attic can run two to three times the cost of blasting, and blasting avoids the drying delay that comes with water-based cleaning.
How much does dry ice blasting mold cost in EAST IRVINE California?
Most residential dry ice blasting jobs in EAST IRVINE run $1,800 to $6,500 in 2026, with a typical attic or crawl space landing near $3,200. Cost depends on square footage blasted, how many cavities are affected, containment complexity, and whether clearance testing is included. Small bathroom framing jobs can come in under $2,000, while a whole-house attic with HVAC mold contamination pushes toward the top of the range.
How does dry ice mold remediation work in EAST IRVINE?
Dry ice mold remediation blasts frozen CO2 pellets at the moldy surface at 150 to 300 psi. The pellets sublimate on impact, lifting mold and biofilm off wood without water or abrasive grit. We contain the area with negative air and HEPA filtration, blast the framing, vacuum the debris, apply an antimicrobial coating, and verify with air sampling. A typical room takes one day; a full attic takes two.
Who offers dry ice blasting mold near me in EAST IRVINE?
Our team offers dry ice blasting mold removal services EAST IRVINE wide, covering Northwood, Woodbridge, Turtle Rock, Quail Hill, and the Great Park area. We run dedicated dry ice blasting machines and keep CO2 pellets in stock, so we are not subcontracting the blast to a third party. Call (833) 929-5837 and we can usually inspect within three business days.
Is dry ice blasting safe for mold removal in EAST IRVINE California?
Yes. Dry ice blasting is safe for wood framing, sheathing, concrete, and most mechanical surfaces when run by a trained technician. The CO2 is food-grade and leaves no chemical residue. The real safety work is containment: negative air machines, HEPA filters, and N95 respirators keep spores out of living space. We follow California Department of Public Health guidelines and test the air before we pull containment.
Licensed, Certified, and Verified
Certifications
Reviews
They blasted our attic after a roof leak and the difference was obvious the same day. What I appreciated was the clearance test: they showed me the before-and-after spore counts and would not pull containment until the numbers were right.
Crawl space mold job in Quail Hill. The crew was on time, contained the space properly, and cleaned up better than they found it. The musty smell was gone within a day, and they sealed the joists so it would not come back.
We had three quotes for bathroom framing mold and this was the only one that explained why dry ice blasting would save the studs. The written scope matched the invoice, and the post-remediation test passed on the first try.
Related Services
Mold Inspection Near Me
Before any dry ice blasting mold job, we run a full inspection with moisture meters and thermal imaging to map every wet pocket. For EAST IRVINE homeowners, that inspection tells us whether blasting is the right method or whether a cavity needs to be opened first.
Mold Inspection Near MeMold Inspection
A standard mold inspection identifies the species, the moisture source, and the spread. We pair it with dry ice blasting mold removal so the inspection findings drive the blast plan instead of guesswork. Most EAST IRVINE inspections take 45 to 90 minutes.
Mold InspectionMold Testing
Lab testing confirms what is growing and at what concentration. We use air sampling pumps and InstaScope readings before and after dry ice mold remediation EAST IRVINE jobs so you have documented proof the spore count dropped to baseline.
Mold TestingMold Testing Near Me
If you need testing fast, we can often schedule same-week sampling in EAST IRVINE. Testing pairs with dry ice blasting mold removal services EAST IRVINE because clearance testing is how we prove the blast worked, not just that the stain is gone.
Mold Testing Near MeCertified Mold Inspector
Our ACAC Certified Mold Inspector supervises every dry ice blasting mold job, from containment setup to final clearance. That credential matters because clearance decisions should be made by someone trained to read spore trap results, not by the crew holding the nozzle.
Certified Mold InspectorBlack Mold Inspection
Black mold growth on framing is one of the most common reasons homeowners call us. A black mold inspection confirms whether the dark staining is Stachybotrys or another species, which determines blast pressure and whether encapsulation is needed after dry ice mold removal EAST IRVINE.
Black Mold InspectionHome Mold Inspection
A home mold inspection covers attic, crawl space, bathrooms, and HVAC closets in one visit. For dry ice blasting mold in EAST IRVINE California, the home inspection is where we decide which cavities get blasted and which just need fogging treatment.
Home Mold InspectionResidential Mold Testing
Residential mold testing gives you room-by-room spore counts. We use those counts to prioritize dry ice blasting mold removal in the worst-affected rooms first, which keeps the project budget focused on the areas that actually need blasting.
Residential Mold TestingCommercial Mold Inspection
Commercial buildings need dry ice blasting mold work scheduled around business hours. We inspect mechanical rooms, tenant spaces, and roof assemblies, then phase the blasting so tenants keep operating. Containment and negative air keep spores out of occupied areas.
Commercial Mold InspectionMold Remediation Company
As a licensed mold remediation company, we handle the full scope: inspection, containment, dry ice blasting mold removal, antimicrobial coating, and clearance testing. You are not coordinating three separate vendors for one attic problem.
Mold Remediation CompanyEmergency Mold Testing Services
When water damage has been sitting for days, emergency mold testing gets scheduled fast. We pair it with dry ice blasting mold near me EAST IRVINE dispatch so testing and blasting happen in the same week instead of dragging out over a month.
Emergency Mold Testing ServicesSame Day Mold Testing
Same day mold testing is available for active water losses in EAST IRVINE. Getting samples the same day means we can start dry ice mold removal EAST IRVINE work as soon as the lab confirms species and concentration, which shortens the overall timeline.
Same Day Mold TestingBasement Mold Inspection
Basement mold often hides behind finished walls and under stair framing. A basement mold inspection with a boroscope inspection camera finds it, and dry ice blasting mold in EAST IRVINE California cleans the framing without tearing out the whole finish.
Basement Mold InspectionAttic Mold Testing And Removal
Attic mold is our most common dry ice blasting mold call. Roof sheathing and rafters collect condensation, and blasting cleans the wood without wetting it further. Attic mold testing and removal includes clearance sampling before the attic is closed up.
Attic Mold Testing And RemovalAir Quality And Mold Testing
Air quality and mold testing measures what you are actually breathing. We run it before and after dry ice blasting mold removal services EAST IRVINE so you can see the spore count drop in the rooms you live in, not just in the cavity we blasted.
Air Quality And Mold TestingMold Remediation Near Me
If you are searching mold remediation near me in EAST IRVINE, we cover Northwood, Woodbridge, Westpark, and Turtle Rock. Dry ice blasting mold is one of the methods we bring, alongside HEPA vacuuming and fogging treatment, depending on the surface.
Mold Remediation Near MeCrawl Space Mold Removal
Crawl space mold thrives on the humidity that builds under a house. Dry ice blasting mold removal cleans joists and subfloor without adding moisture, and we follow with encapsulation sealant on the framing to keep it from returning next wet season.
Crawl Space Mold RemovalBathroom Mold Removal Service
Bathroom mold grows on studs behind tile and on ceiling drywall. When the wall is opened, dry ice blasting mold in EAST IRVINE California cleans the framing so new drywall goes back onto clean wood instead of contaminated studs.
Bathroom Mold Removal ServiceToxic Mold Removal
Toxic mold removal requires stricter containment and verified clearance. Dry ice blasting mold fits that protocol because it removes spores without chemical residue, and our ACAC Certified Mold Inspector signs off on the air sampling before containment comes down.
Toxic Mold RemovalMold Abatement
Mold abatement is the containment-and-removal phase, and dry ice blasting mold is one of the tools we use inside it. Negative air machines, HEPA filters, and plastic sheeting keep the abatement zone sealed while we blast the framing clean.
Mold AbatementProfessional Mold Removal
Professional mold removal means documented process, trained crews, and clearance testing. Our dry ice blasting mold removal services EAST IRVINE include all three, with before-and-after lab results you can hand to an insurer or a buyer.
Professional Mold RemovalMold Cleanup Near Me
Mold cleanup near me searches usually mean visible growth and a musty smell. We inspect, contain, and clean with dry ice blasting mold removal, then fog the cavity with Benefect or Concrobium so the odor source is treated, not masked.
Mold Cleanup Near MeWater Damage Mold Remediation
Water damage mold remediation starts with fixing the moisture source. We find the leak, dry the cavity with dehumidifiers and air scrubbers, then run dry ice blasting mold in EAST IRVINE California to clean the framing before it is closed back up.
Water Damage Mold RemediationMold Spore Testing
Mold spore testing tells you what is airborne and at what concentration. We use air sampling pumps and InstaScope readings to compare indoor counts against an outdoor control, which is how we prove dry ice mold remediation EAST IRVINE actually reduced exposure.
Mold Spore TestingPost Remediation Mold Testing
Post remediation mold testing is the final gate on every dry ice blasting mold job. We sample 24 to 48 hours after the antimicrobial coating cures. If counts are still elevated, we re-blast and re-test at no additional charge.
Post Remediation Mold TestingMold Fogging Treatment
Mold fogging treatment reaches the surfaces a blaster cannot touch, like the inside of wall cavities and ductwork. We pair fogging with dry ice blasting mold removal so the framing is physically cleaned and the residual spores are chemically knocked down.
Mold Fogging TreatmentAffordable Mold Remediation
Affordable dry ice mold remediation in EAST IRVINE starts with scoping only the affected cavities. Because blasting avoids tear-out, we often save homeowners the cost of replacing framing and drywall, which is where most of the budget goes on a mold job.
Affordable Mold Remediation24 Hour Mold Removal
24 hour mold removal is for active water losses where mold will bloom within days. We can dispatch emergency testing and start dry ice blasting mold removal as soon as the source is controlled, which is often the difference between cleaning framing and replacing it.
24 Hour Mold RemovalOdor Removal Mold
Musty odors come from mold colonies and the microbial compounds they release. Odor removal mold work starts with finding the colony, and dry ice blasting mold in EAST IRVINE California removes it at the source so the smell does not come back after the deodorizer fades.
Odor Removal MoldSchedule Dry Ice Blasting Mold in EAST IRVINE, California
If you have found mold on framing, sheathing, or crawl space joists, call us at (833) 929-5837. We will inspect, quote the blast scope in writing, and schedule the work, often within the same week. Every job ends with clearance testing so you know the spores are gone.